autogenerated headers for rev https://github.com/mavlink/mavlink/tree/e2214937227270c64d01635a6578e9b531e8aeb7

autoquad/autoquad.h

@@ -76,7 +76,7 @@ typedef enum MAV_CMD
 	MAV_CMD_NAV_LAND_LOCAL=23, /* Land at local position (local frame only) |Landing target number (if available)| Maximum accepted offset from desired landing position [m] - computed magnitude from spherical coordinates: d = sqrt(x^2 + y^2 + z^2), which gives the maximum accepted distance between the desired landing position and the position where the vehicle is about to land| Landing descend rate [ms^-1]| Desired yaw angle [rad]| Y-axis position [m]| X-axis position [m]| Z-axis / ground level position [m]|  */
 	MAV_CMD_NAV_TAKEOFF_LOCAL=24, /* Takeoff from local position (local frame only) |Minimum pitch (if airspeed sensor present), desired pitch without sensor [rad]| Empty| Takeoff ascend rate [ms^-1]| Yaw angle [rad] (if magnetometer or another yaw estimation source present), ignored without one of these| Y-axis position [m]| X-axis position [m]| Z-axis position [m]|  */
 	MAV_CMD_NAV_FOLLOW=25, /* Vehicle following, i.e. this waypoint represents the position of a moving vehicle |Following logic to use (e.g. loitering or sinusoidal following) - depends on specific autopilot implementation| Ground speed of vehicle to be followed| Radius around MISSION, in meters. If positive loiter clockwise, else counter-clockwise| Desired yaw angle.| Latitude| Longitude| Altitude|  */
-	MAV_CMD_NAV_CONTINUE_AND_CHANGE_ALT=30, /* Continue on the current course and climb/descend to specified altitude.  When the altitude is reached continue to the next command (i.e., don't proceed to the next command until the desired altitude is reached. |Empty| Empty| Empty| Empty| Empty| Empty| Desired altitude in meters|  */
+	MAV_CMD_NAV_CONTINUE_AND_CHANGE_ALT=30, /* Continue on the current course and climb/descend to specified altitude.  When the altitude is reached continue to the next command (i.e., don't proceed to the next command until the desired altitude is reached. |Climb or Descend (0 = Neutral, command completes when within 5m of this command's altitude, 1 = Climbing, command completes when at or above this command's altitude, 2 = Descending, command completes when at or below this command's altitude. | Empty| Empty| Empty| Empty| Empty| Desired altitude in meters|  */
 	MAV_CMD_NAV_LOITER_TO_ALT=31, /* Begin loiter at the specified Latitude and Longitude.  If Lat=Lon=0, then loiter at the current position.  Don't consider the navigation command complete (don't leave loiter) until the altitude has been reached.  Additionally, if the Heading Required parameter is non-zero the  aircraft will not leave the loiter until heading toward the next waypoint.  |Heading Required (0 = False)| Radius in meters. If positive loiter clockwise, negative counter-clockwise, 0 means no change to standard loiter.| Empty| Empty| Latitude| Longitude| Altitude|  */
 	MAV_CMD_NAV_ROI=80, /* Sets the region of interest (ROI) for a sensor set or the vehicle itself. This can then be used by the vehicles control system to control the vehicle attitude and the attitude of various sensors such as cameras. |Region of intereset mode. (see MAV_ROI enum)| MISSION index/ target ID. (see MAV_ROI enum)| ROI index (allows a vehicle to manage multiple ROI's)| Empty| x the location of the fixed ROI (see MAV_FRAME)| y| z|  */
 	MAV_CMD_NAV_PATHPLANNING=81, /* Control autonomous path planning on the MAV. |0: Disable local obstacle avoidance / local path planning (without resetting map), 1: Enable local path planning, 2: Enable and reset local path planning| 0: Disable full path planning (without resetting map), 1: Enable, 2: Enable and reset map/occupancy grid, 3: Enable and reset planned route, but not occupancy grid| Empty| Yaw angle at goal, in compass degrees, [0..360]| Latitude/X of goal| Longitude/Y of goal| Altitude/Z of goal|  */