hm/c_library_v2
1
0
Fork 0
Code Issues Pull Requests Actions Packages Projects Releases Wiki Activity

autogenerated headers for rev https://github.com/mavlink/mavlink/tree/3cc4127e2e7394ff33a87b1dcc0971284ea5131f

Browse Source
This commit is contained in:
PX4BuildBot
2017-04-11 04:18:28 +00:00
parent 6a09acb3c9
commit 5849e766d8
7 changed files with 7 additions and 7 deletions
Download Patch File Download Diff File Expand all files Collapse all files
slugs/slugs.h
+1 -1
View File
@@ -101,7 +101,7 @@ typedef enum MAV_CMD
MAV_CMD_DO_GUIDED_LIMITS=222, /* set limits for external control |timeout - maximum time (in seconds) that external controller will be allowed to control vehicle. 0 means no timeout| absolute altitude min (in meters, AMSL) - if vehicle moves below this alt, the command will be aborted and the mission will continue. 0 means no lower altitude limit| absolute altitude max (in meters)- if vehicle moves above this alt, the command will be aborted and the mission will continue. 0 means no upper altitude limit| horizontal move limit (in meters, AMSL) - if vehicle moves more than this distance from it's location at the moment the command was executed, the command will be aborted and the mission will continue. 0 means no horizontal altitude limit| Empty| Empty| Empty| */
MAV_CMD_DO_ENGINE_CONTROL=223, /* Control vehicle engine. This is interpreted by the vehicles engine controller to change the target engine state. It is intended for vehicles with internal combustion engines |0: Stop engine, 1:Start Engine| 0: Warm start, 1:Cold start. Controls use of choke where applicable| Height delay (meters). This is for commanding engine start only after the vehicle has gained the specified height. Used in VTOL vehicles during takeoff to start engine after the aircraft is off the ground. Zero for no delay.| Empty| Empty| Empty| Empty| Empty| */
MAV_CMD_DO_LAST=240, /* NOP - This command is only used to mark the upper limit of the DO commands in the enumeration |Empty| Empty| Empty| Empty| Empty| Empty| Empty| */
MAV_CMD_PREFLIGHT_CALIBRATION=241, /* Trigger calibration. This command will be only accepted if in pre-flight mode. Except for Temperature Calibration, only one sensor should be set in a single message and all others should be zero. |1: gyro calibration, 3: gyro temperature calibration| 1: magnetometer calibration| 1: ground pressure calibration| 1: radio RC calibration, 2: RC trim calibration| 1: accelerometer calibration, 2: board level calibration, 3: accelerometer temperature calibration| 1: APM: compass/motor interference calibration / PX4: airspeed calibration| 1: ESC calibration, 3: barometer temperature calibration| */
MAV_CMD_PREFLIGHT_CALIBRATION=241, /* Trigger calibration. This command will be only accepted if in pre-flight mode. Except for Temperature Calibration, only one sensor should be set in a single message and all others should be zero. |1: gyro calibration, 3: gyro temperature calibration| 1: magnetometer calibration| 1: ground pressure calibration| 1: radio RC calibration, 2: RC trim calibration| 1: accelerometer calibration, 2: board level calibration, 3: accelerometer temperature calibration| 1: APM: compass/motor interference calibration (PX4: airspeed calibration, deprecated), 2: airspeed calibration| 1: ESC calibration, 3: barometer temperature calibration| */
MAV_CMD_PREFLIGHT_SET_SENSOR_OFFSETS=242, /* Set sensor offsets. This command will be only accepted if in pre-flight mode. |Sensor to adjust the offsets for: 0: gyros, 1: accelerometer, 2: magnetometer, 3: barometer, 4: optical flow, 5: second magnetometer, 6: third magnetometer| X axis offset (or generic dimension 1), in the sensor's raw units| Y axis offset (or generic dimension 2), in the sensor's raw units| Z axis offset (or generic dimension 3), in the sensor's raw units| Generic dimension 4, in the sensor's raw units| Generic dimension 5, in the sensor's raw units| Generic dimension 6, in the sensor's raw units| */
MAV_CMD_PREFLIGHT_UAVCAN=243, /* Trigger UAVCAN config. This command will be only accepted if in pre-flight mode. |1: Trigger actuator ID assignment and direction mapping.| Reserved| Reserved| Reserved| Reserved| Reserved| Reserved| */
MAV_CMD_PREFLIGHT_STORAGE=245, /* Request storage of different parameter values and logs. This command will be only accepted if in pre-flight mode. |Parameter storage: 0: READ FROM FLASH/EEPROM, 1: WRITE CURRENT TO FLASH/EEPROM, 2: Reset to defaults| Mission storage: 0: READ FROM FLASH/EEPROM, 1: WRITE CURRENT TO FLASH/EEPROM, 2: Reset to defaults| Onboard logging: 0: Ignore, 1: Start default rate logging, -1: Stop logging, > 1: start logging with rate of param 3 in Hz (e.g. set to 1000 for 1000 Hz logging)| Reserved| Empty| Empty| Empty| */